中央吸塵系統是用PVC管道網絡，將設計配置在廠房墻面上的吸塵閥門接口與安裝在生活區域之外的工作主機相連接的一種出彩吸塵系統。使用時將吸塵器軟管插入某一個接口，按動開關系統就會開始工作。所有的灰塵和碎片都會被吸附，并被排放到生活區域之外。從而避免了普通吸塵器的出眾噪音并且有效解決了傳統吸塵器工作時產生的室內空氣二次污染問題。加尼福尼亞大學的研究成果表明，經常性地使用中央吸塵系統進行室粉塵治理和換氣，可減輕室內過敏癥狀及呼吸道哮喘癥達60%以上。

The central vacuum system is an advanced vacuum system that uses a PVC pipeline network to connect the vacuum valve interface designed and configured on the factory wall with the working host installed outside the living area. When using, insert the vacuum cleaner hose into a certain interface and press the switch to start the system working. All dust and debris will be adsorbed and discharged outside the living area. This avoids the high-end noise of ordinary vacuum cleaners and completely solves the problem of secondary indoor air pollution caused by traditional vacuum cleaners during operation. The research results of the University of California indicate that regularly using a central vacuum system for indoor dust control and ventilation can reduce indoor allergy symptoms and respiratory asthma by more than 60%.

木工中央除塵設備是適合所有木制品生產加工企業的環保治理設備，能有效的集中收集家具廠、地板廠、木門廠在生產加工過程中使用木工機械所產生的木屑與粉塵，保證了車間的生產環境和工作人員的深意健康。木工中央除塵設備采用負壓式動力風機（5.5KW—75KW）有效的規避了常規吸附過程中木屑對動力所產生的破壞，在不影響吸附效果的同時大大的增加了動力風機的使用壽命。管道設計采用全密封中央式鋪設螺旋管道，保證吸附的壓力提高使用效率。根據動力參數可定制相應的脈沖過濾系統，優化過濾面積化的分離空氣與粉塵并防止粉塵的二次飛揚做到集中處理。通過觀察口可隨時觀測木屑粉塵收集情況并能隨時進行統一處理，清灰方便。全自動變頻控制系統是智能控制除塵設備耗電的控制系統，根據車間生產的機械設備使用率自動調整風機轉速并能有效的節約能源。木工中央除塵設備服務于大中小型木工制作加工企業，有效的改善了生產車間的工作環境，減少了火災的發生率，并保證了工作人員的身體健康，得到了廣大的好評。

The central dust removal equipment for woodworking is an environmental management device suitable for all woodworking production and processing enterprises. It can effectively collect wood chips and dust generated by woodworking machinery used in furniture factories, flooring factories, and wooden door factories during the production and processing process, ensuring the production environment of the workshop and the deep health of the workers. The central dust removal equipment for woodworking uses negative pressure power fans (5.5KW-75KW) to effectively avoid the damage caused by wood chips to the power during the conventional adsorption process, greatly increasing the service life of the power fans without affecting the adsorption effect. The pipeline design adopts a fully sealed central laying spiral pipeline to ensure the adsorption pressure and improve the efficiency of use. According to the power parameters, a corresponding pulse filtration system can be customized to optimize the separation of air and dust with a larger filtration area and prevent secondary dust flying for centralized processing. The collection of sawdust can be observed at any time through the observation port and unified treatment can be carried out at any time, making dust cleaning convenient. The fully automatic frequency conversion control system is an intelligent control system for power consumption of dust removal equipment. It automatically adjusts the fan speed according to the usage rate of mechanical equipment produced in the workshop and can effectively save energy. The central dust removal equipment for woodworking serves large, medium, and small woodworking manufacturing and processing enterprises, effectively improving the working environment of production workshops, reducing the incidence of fires, and ensuring the physical health of workers, receiving widespread praise.

1、 中央吸塵系統安裝

1. Installation of central vacuum system

1.1 主機定位根據吸塵主機選擇的型號，按照施工圖紙，確定主機位置。基本原則是主機底部離地面15mm以上，周圍環境建議通風干燥。如果安裝在室外，建議加裝防雨措施。否則不予保修。

1.1 Host positioning: Based on the selected model of the vacuum cleaner host and the construction drawings, determine the location of the host. The basic principle is that the bottom of the host must be at least 15mm above the ground, and the surrounding environment must be ventilated and dry. If installed outdoors, rain protection measures must be added. Otherwise, no warranty will be provided.

1.2 24V信號線的連接：24V輸出電源插座與信號線的連接建議用壓線鉗進行鉗壓，使用壓線鉗時要準確選用1mm2 的壓口進行鉗壓。

1.2 Connection of 24V signal line: The connection between the 24V output power socket and the signal line must be clamped with a crimping tool. When using a crimping tool, a 1mm2 crimping port should be accurately selected for crimping.

1.3 根據圖紙標注在規定的位置預留相對應主機型號的電源插座。

1.3 Reserve power sockets corresponding to the host model at the designated locations according to the drawings.

2、 吸塵管的安裝 吸塵主管道采用直徑50毫米的PVC管材及配件，按照圖紙實施安裝，橫向管網一般情況下安裝吊頂內，豎向管網墻面開槽隱蔽安裝。電線管采用直徑16毫米的PVC電工管材隨主吸塵管道或另辟路徑安裝，只要保證每個插口均有24V信號電源即可。

2. The installation of the vacuum pipe is carried out using a 50mm diameter PVC pipe and accessories for the main vacuum pipe. The installation is carried out according to the drawings. The horizontal pipe network is generally installed inside the ceiling, while the vertical pipe network is installed with concealed grooves on the wall. The electrical conduit is made of PVC electrical pipe with a diameter of 16mm, which can be installed along the main vacuum pipe or through a separate path, as long as each socket has a 24V signal power supply.

2.1 主管網選用直徑50PVC吊頂安裝：建議嚴格執行安裝規程，固定裝置（管卡、吊定裝置，依此類推。如果管道只有2.5米長，那么兩端各留25厘米，中間距離按不大于1米等份設置；如果管道改變直線安裝，在轉彎處起點25厘米處安裝固定裝置，原理同上。管道水平安裝建議平直，無扭曲，無機械應力產生，管道鋸口要整齊，用0＃砂紙將管口毛刺打磨光滑，用干凈的布塊將管口內外擦干凈，膠水涂抹要均勻適量。

2.1 Installation of PVC suspended ceiling with a diameter of 50cm for the main pipeline network: The installation regulations must be strictly followed, and the fixing devices (pipe clamps, hanging devices, and so on) must be used. If the pipeline is only 2.5 meters long, leave 25 centimeters at each end, and set the middle distance in equal parts of no more than 1 meter. If the pipeline is installed in a straight line, the fixing device should be installed at the starting point of 25 centimeters at the turning point. The principle is the same as above. The pipeline must be installed horizontally and straight, without distortion or mechanical stress. The pipe saw should be neat, and the burrs on the pipe mouth should be polished smooth with 0 # sandpaper. The inside and outside of the pipe mouth should be wiped clean with a clean cloth, and the glue should be evenly.

2.2 墻面開槽埋管安裝：根據圖紙準確定位，墻面槽寬不得大于10厘米，深度8厘米，槽線建議用墨線定位，用切割機將線槽切出較明顯痕跡后，再用鋼鑿進行開槽。管道在墻槽內應呈自然狀態放置，不得有機械應力產生，且每隔1米用固定裝置將管道連同線管一起固定。待管網安裝完畢后，經過檢查合格后用水泥沙漿將墻槽進行封閉，嚴禁管道高于墻的基準面。

2.2 Wall slotting and buried pipe installation: Accurately locate according to the drawings. The width of the wall groove should not exceed 10 centimeters and the depth should be 8 centimeters. The groove line must be positioned with ink lines. After cutting the groove with a cutting machine to make obvious marks, use a steel chisel to make the groove. The pipeline should be placed in a natural state within the wall groove, without any mechanical stress, and fixed together with the conduit every 1 meter using a fixing device. After the installation of the pipeline network is completed, the wall groove shall be sealed with cement mortar after passing the inspection, and it is strictly prohibited for the pipeline to be higher than the reference level of the wall.

2.3 信號線穿管安裝：信號線使用1mm2 BV國標線，電線管使用直徑20mm阻燃PVC線管。電線管安裝一般情況下隨主管網到各插口閥，也可以采用另辟路徑進行安裝，只要能滿足使用要求即可。線管的固定方式采用直徑20迫碼貼墻、貼頂固定，固定迫碼從線管起始點20厘米開始每隔0.5米一個，依此類推。線管的走向要合理，應該與電氣安裝形成一個統一綜合體，所有插口閥處的信號線采用并聯方式接線，且建議與吸塵主機處24V電源成通路狀態。

2.3 Installation of signal line conduit: The signal line uses 1mm2 BV national standard line, and the wire conduit uses 20mm diameter flame-retardant PVC conduit. In general, the installation of electrical conduits follows the main pipeline network to each socket valve, or alternative paths can be used for installation as long as they meet the usage requirements. The fixing method of the conduit is to use a diameter of 20 to fix it to the wall or top. The fixed clamps are placed every 0.5 meters from the starting point of the conduit, starting from 20 centimeters, and so on. The direction of the conduit should be reasonable and form a unified complex with the electrical installation. All signal lines at the socket valves should be connected in parallel and must be in a connected state with the 24V power supply at the vacuum cleaner host.

2.4 管網試壓后將墻槽用水泥沙漿填充，之后在上面用記號筆或其它醒目標志標明“內有PVC管線，請勿損壞”的字樣，以防他人在不知情的情況下將吸塵管網損壞。

2.4 After the pressure test of the pipeline network, fill the wall groove with cement mortar, and then use a marker pen or other conspicuous signs to indicate the words "PVC pipeline inside, do not damage" on it, to prevent others from damaging the vacuum pipe network without knowledge.